Unit Code :- MOD006111
Unit Title :- Structural Method And Analysis
Introduction :-
This is the assessment element 010-coursework for module_MOD006111_Structural Method and Design. It carries 40% of the final mark for the module and has a qualifying mark of 30%. The module has an over all pass mark of 40%.This assessment is project-oriented on structural analysis and design and includes both problem solving and reflective questions.
MOD006111 Structural Method And Analysis Assignment E010 – UK
Coursework brief :-
Figure 1 below shows a structural layout/grid of a five-storey building with a height of 4 m for each storey. The whole building structure consists of a simply constructed steel frame for the gridlines 1 to 3 and a simply constructed concrete frame for the gridlines 4 to 6. It carries a 150 mm thick pre-cast reinforced concrete floor. The variable action on the floor depth of concrete beam spacing and spans of both steel and concrete beams have been tabulated in the table 1 below against your SID.
You are required to design and detail typical structural members of the building structure and submit a technical report of your design and detailing with the evidence of design calculation to the current Code of Practice -Structural Euro codes as appendix to each question below.
MOD006111 Structural Method And Analysis Assignment E010 – UK
Q 1 –Design and detail the reinforced concrete beam B/5-6 using the design data of materials reinforcments and design data provided below:
• Concrete grade C30 fck =30 N/mm2
• Design tensile strength of the concrete fctm =2.9 N/mm2
• Maximum aggregate size of the concrete =20 mm
• Yield strength of main steel reinforcement fyk =500 N/mm2
• Yield strength of transverse links fwyk =500 N/mm2
• Diameter of main reinforcement for a beam ds = 25mm
• Diameter of transverse links dL = 10mm
• 15% moment redistribution δ = 0.85
• Concrete cover to the reinforcements in concrete beam c = 25mm
• Unit weight of concrete γ = 25 kN/m3
• Width of a beam section b =300mm
a. Identify the concrete beam in the structural grid and calculate design action bending moment and shear force before draw the BMD and SFD.
b. Carry out bending design and detailing for the main reinforcements.
c. Carry out shear design and detailing for the transverse links.
d. Check by calculation whether the beam satisfies deflection requirements.
e. List the measures you have taken to control the cracking of concrete.
f. Detail both construction drawings and table of reinforcements.
MOD006111 Structural Method And Analysis Assignment E010 – UK
Q2 –Design and detail the steel beam B/1-2 with an assumption of all the steel beams in the building floor using UKB section in grade of S275.
a. Identify the beam in the structural grid and calculate the design action bending moment and shear force before draw the BMD and SFD.
b. Determine by calculation a suitable UKB section for the beam and check by calculation whether the chosen section satisfies the design requirements with regard to bending shear and deflection respectively if it is laterally restrained along the span.
c. Use the SCI design table to check whether the above chosen UKB section is still adequate if the beam is only laterally restrained at both ends.
d. Use the SCI Tables to re-choose a UKB section for the beam B/1-2 and validate by manual calculation its adequacy on bending shear and deflection.
Q3 –Design and detail the steel column B/2 with an assumption of all the steel columns in the building floor using UKC section in grade of S275
a. Identify the column in the structural grid and calculate its design action and design axial force.
b. Determine by calculation a suitable UKC section for the column if it is prevented from buckling about both major and minor axes under an axial force only.
c. If the column is hold at both ends, partially restrained about its major y-y and effectively restrained about its minor axis z-z check by calculation whether the above chosen UKC section is still adequate for the column under the axial force only.
d. Use the SCI design table to re-choose a section for the column B/2 and validate by calculation its adequacy under the axial force only.
Q4 – Critically compare the bending performance, strain and stress status at the ultimate limit state and design bending resistance of a singly reinforced concrete beam a restrained steel beam and a timber beam.
Q5. Report writing with the above design calculation sheets as its Appendices.
a. Introduction and Methodology
b. Results and Discussion
c. Conclusion and Reflection.
d. Clarity of explanation and analysis, spelling and grammar.
MOD006111 Structural Method And Analysis Assignment E010 – UK
3.Please note:
a. You need to use YOUR design parameters in Table 1 to process YOUR design calculation independently. A deduction of 50% mark will be applied to the marks of your work if you do not use your unique parameters as given in Table 1.
b. You need to perform your design and detailing calculation to the current legal documentation of Code of Practice Structural Euro codes. A deduction of 50% mark will be applied to the marks of your work if your design and calculation was not performed in accordance with the current code of practice Structural Euro code.
c. You need to answer all the questions clearly and neatly on A4 paper with the aid of an annotated sketch where necessary. You need to put your answer sheets in the order of the question numbers before scanning and saving them into ONE pdf document for the submission and marking via Canvas/Turnitin. Detailed instructions for submission of your coursework are given on Canvas.
d. You must include your SID in each page of your coursework. You must carefully read and understand all the submission instructions before starting this assessment. Up to 10% mark deduction will be applied if your answer sheets are poorly presented.
ORDER This MOD006111 Structural Method And Analysis Assignment NOW And Get Instant Discount
